This is the ultimate in high performance Race proven off-road suspension. This system will give you up to 18″ of travel with a massive 1.5″ lower mono balls and 1″ uppers; just like the Trophy Trucks. The lower pivots are not urethane, or Delrin they are massive 1″ mono balls. This kit is high end so if you are looking for the best off-road system for your A-Arm Ranger you have found it.
This kit is high end so if you are looking for the best off-road system for your A-Arm Ranger you have found it. This system will give you up to 18″ of travel with a massive 1.5″ lower mono balls and 1″ uppers; just like the Trophy Trucks.
The Camburg long travel off road system is by far the best available for the Ranger Edge. This is the same system we used on our Ranger Edge race truck. We have raced with this system at the 2005 Baja 1000 and the 2006 Baja 500 in the Trophy Truck class. This system will yield 19″ of wheel travel (with no ac fan box). This system utilizes a full box construction lower arm with 1 1/2″ lower uni balls and 1″ uniballs for the lower arm pivots (no urethane bushings here). The upper arm is made with 1 1/2″ .120 wall tube, the reason we do this is to fit a coilover and a by pass shock. This system also comes with a full stainless steel steering system, 17-4 stainless inner clevis, and spacers along with the stainless tie rods. Because of the high wheel travel numbers we achieve we use a 1″ outer heim joint and a 3/4″ inner heim.
The Camburg long travel off road system is by far the best available for the Ranger Edge. This is the same system we use on our Ranger Edge race truck. We have raced with this system at the 2005 Baja 1000 and the 2006 Baja 500 in the Trophy Truck class. This system will yield 19″ of wheel travel (with no ac fan box).
We have a wide selection of rear shocks to meet your needs and budget. The Bilstein 5100 shocks are great for all around use and more tailored for a plush street ride. Stepping up to FOX’s 2.0 Performance Series shock has a larger aluminum shock body which holds more oil for better shock performance offroad and has a firmer ride.
When you are ready to take your 5.5 Performance kit to the next level the 2.0 shock upgrade is a great choice. This shock mount is designed to utilize a 2.0 x 8-8.5″ travel remote reservoir shock. This shock upgrade is a level 8 to install so we recommend a high end off-road fabrication shop to do the install.This kit must be welded on and does not include shocks.
Looking to upgrade your single shock Camburg kit Ranger Edge 6.0 to our dual shock version? The upper mount welds to the frame and the lower mount welds to the lower arm. This setup gives you maximum wheel travel with our kit.
Ford Rangers are known for thin and weak upper arm mounts on the frame and are prone to them cracking and tearing off. Our Camburg frame gusset kit welds to the stock upper arm mounts and makes them bullet proof.
Our Camburg upper arm mount frame gusset kit will help strengthen your frames weak link. The upper arm mounts can and will tear out under extreme conditions and hardcore driving. This gusset kit will work with most suspension systems out there. Also included is the lower frame bump stop reinforcement. This is a plate that gets welded under the frame where the lower a-arm bump stop hits the frame. This will add 200% more material to this location. This kit is made of laser cut 3/16″ steel and comes complete with 10 gussets.
Our Camburg limit straps are made in the USA and quad wrapped for the ultimate strength from military grade materials. The mounting tabs are 4130 chromoly and plated black for corrosion resistance. These won’t stretch like cheaper versions will that are made overseas.
With heims and uniballs you want to make sure you use the right lube and not a grease or oil that attracts dirt. Tri-flow is a teflon (PTFE) based lube that goes on wet and drys to a film to coat and seal the surfaces. You only need to use 3-4 drops per uniball or heim.
An easy way to mount a limit strap to the frame/chassis is using this clevis. It gives you the ability to adjust the strap length so initial setup is not as critical and you can re-adjust if the strap stretches over time or if you miscalculated the location slightly. You will need to make the mount this fits into from a piece of tubing.
Camburg Engineering is the leader in off-road suspension systems and is at the forefront in technology and design. Our over the counter parts are being race tested constantly and have won numerous championships, so if you are looking for the most proven long travel or performance suspension systems Camburg is your #1 choice.