This kit is what’s required to rebuild the uniballs in your Camburg upper arms. The kit includes two FK Made in the USA PTFE-lined uniballs and two snap rings. Confirm sizing before ordering as some older version arms use a smaller 1.00″ uniball.
FOX 2.5 Factory Series IFP Coilovers are valved specifically for your application, we are able to gain 0-2.5 inches of lift and increase wheel travel as well. In addition, by replacing the stock ball-joint with a uni-ball bearing, we can increase wheel travel with a part that is considerably stronger and will last longer under extreme conditions. In the rear we go with a pair of FOX’s 2.0 Performance Series shocks to provide a firmer ride and better offroad performance.
With Bilstein’s NEW 6112 line of adjustable shocks we’ve put together a great suspension kit for that customer looking to lift the front of their Tacoma, improve the ride quality both on and off-road all while staying within a price point that maximizes your gains.
If you’re looking to level out your Tacoma without breaking the bank, our Bilstein kit is a great choice. We use Bilstein’s 5100 Series adjustable front shocks in combination with our ball-joint upper arms. The Bilstein’s give you the ability to raise the front end at a few different levels and are valved/setup for the increased ride height for better handling and control.
Designed for the serious off-road adventure seeker, the all new BILSTEIN 6112 Series Kit is the ultimate suspension solution. The 6112 Series optimizes off-road and on-road capabilities with a 60mm digressive piston for increased damping control.
In this high end Camburg Long Travel kit you will find nothing but the very best in A-Arm performance. Starting with our lower arm, uni-balls in the lower frame pivots, uni-ball lower ball joint replacement, and a stout boxed race arm. If you are into trail running, desert racing or just exploring Moab, you have found the ultimate in performance!
In this high end Camburg Long Travel kit you will find nothing but the very best in A-Arm performance. Starting with our lower arm, uni-balls in the lower frame pivots, uni-ball lower ball joint replacement, and a stout boxed race arm. The upper arm pivots on urethane bushings with zerk fitting and 1.25″ uniballs replace the stock ball joints. We adapt the uniball to the spindle with heat treated stainless steel adapters.
These arms gives many of the same benefits our uniball upper arms offer at a lower cost. The ball-joint arms also hold up better under wet harsh conditions compared to a uniball since it’s a sealed & greased joint. With Toyota’s newer chassis, the factory ball-joint is considerably stronger & larger than in previous years. By building an upper arm to re-angle the ball-joint, you’re able to gain more wheel travel with extended length coilovers from Bilstein, FOX, King and Icon and keep the joint in its normal operating range.
When lifting your truck, the stock upper arms become the limiting factor and hold back your suspensions performance. Our Camburg upper arms address these issues and more. Replacing the stock ball-joint with a uniball bearing we’re able to gain wheel travel with a part that is considerably stronger and will last longer under extreme conditions. We build more caster and change the camber curve to correct geometry so the vehicle aligns correctly and improves driving characteristics and handling. our ball joint arms have a corrected angle to maximize travel.
We now have machined covers for our Camburg ball-joint upper arms. These cap off the top of the arms to protect the MOOG ball-joint and utilize an o-ring seal & press fit. We machine these in-house from 6061-T6 billet aluminum, anodize them black and laser our trademark Camburg logo on them.
These are our 4″ lift spindles for the 2005-2017 Tacoma Prerunners. These are a great solution for larger tires and factory ride or much need clearance for larger tires with our bolt in mid travel coilover or long Travel kits. Factory spindles are known for bending so this new design is much stronger than the factory units giving you strength needed for off road use.
Toyota didn’t make it easy to remove the factory upper arm frame bolts, especially on the 2014-2016 models where it’s almost impossible. We recommend replacing the bolts with new OEM Toyota bolts to simplify the installation process.
FOX now offers their standard Factory 2.5 remote reservoir version and for the ultimate combination their new DSC version. Both shocks have a 2.5″ diameter shock body for added oil capacity for aggressive use both on and offroad. Based on their race shocks, they are fully rebuild-able and revalve-able for optional tuning and maintenance.
The FOX Factory Series Coil-over IFP shocks provide improved damping in any terrain. Coil-over shocks provide suspension damping and suspend the weight of the vehicle. The integrated coil spring can be adjusted for preload and ride height and come pre-set to level your vehicle right out of the box. Experience for yourself the incredible performance and precise control that Factory Series Coil-overs IFP shocks deliver. These 2.5 coilovers are designed to be used with our Camburg upper arms for maximum useable wheel travel and performance.
For the newer Toyota Tacomas, KING offers their 2.5 series coilovers in a remote reservoir configuration with an optional external compression adjuster for fine tuning. These bolt right in and include the necessary brackets to mount the reservoirs to the frame.
This is a a great way to level out your truck and improving the ride on a budget. Cheap spacers lifts do nothing but create problems and reduce wheel travel. Bilstein’s 5100 shocks give you the ability to raise the front end at 3 different levels and are valved internally for the raised height and better handling. You re-use the OEM coil springs to keep the cost down. This is by far the best entry level lift to install.
FOX now offers their Factory 2.5 piggyback reservoir shock for the rear of the Silverado. For the ultimate combination they have it available with their new DSC version. Both shocks have a 2.5″ diameter shock body for added oil capacity for aggressive use both on and offroad.
For the newer Toyota Tacoma’s, KING offers their 2.5 series rear shocks in a remote reservoir configuration with an optional external compression adjuster for fine tuning. These bolt right in and include the necessary brackets to mount the reservoirs to the frame. These are for 0-1.5″ of lift over stock in the rear.
We have a wide selection of rear shocks to meet your needs and budget. The Bilstein 5100 shocks are great for all around use and more tailored for a plush street ride. Stepping up to FOX’s 2.0 Performance Series shock has a larger aluminum shock body which holds more oil for better shock performance offroad and has a firmer ride. Bilstein also offers a 5160 with a remote res that is also longer for more wheel travel.
Looking to lift the rear of your truck? We use the best leafs springs out there manufactured in the USA by Deaver Spring who’s been in the business for over 100 years. They are progressive for better bottoming control when off-roading but plush when driven on the street for a much better ride compared to stock both on and off-road. Some models have a mini-pak available at a lower cost that replaces the factory over-load spring with a 3-5 leaf pack for added lift and progression. Most Deaver springs are not designed for heavy hauling and heavy towing.
Looking to adapt a heim to your factory steering rack? Our steering clevis’s and clevis bolts are CNC machined from heat-treated 17-4 H1150 stainless steel for maximum strength. Our design has the least amount of bumpsteer due to our design compared to other aftermarket versions. We supply stainless heim spacers to be used with a standard 3/4″ x 3/4″ heim joint (JMX-12T).
Looking to add a bypass shock to our long-travel kit? Our weld-on shock mount takes the guess work out and speeds up the process.These weld onto the frame and locate off the top of the coil bucket and tie into the frame 3 spots per side for maximum strength.
These are the axle shafts needed with our long-travel kits for your 4wd truck.
They are CNC machined from 4340 chomoly, then heat-treated, stress relieved and powdercoated black. They are designed to be used with the OEM parts, not aftermarket or re-manufactured units as those don’t match up to the factory spline count and diameters.
An easy way to mount a limit strap to the frame/chassis is using this clevis. It gives you the ability to adjust the strap length so initial setup is not as critical and you can re-adjust when the strap stretches over time so that you’re not allowing the suspension to droop out too far. You will need to make the mount this fits into.
Complete hardware kit for Camburg 1.25″ uniball upper control arms. If you have older arms that use a 1.00″ uniball and hex head bolt, make a note of that in the notes section as it will be a different kit.
Looking to replace some of the individual parts for your Camburg upper arms? Here are some of the small parts used on our kits. We also offer a complete hardware kit, a bushing and sleeve kit and uniball kits separately.
We now have available the same polyurethane grease we supply with our upper arms in a grease tube to load into a grease gun and charge through zerk fittings. This is the BEST grease to use for any polyurethane bushings from upper arms to leaf springs. It contains versatile water-proof, non-melting Teflon and is formulated to seal out water and to lubricate under the most adverse conditions. It’s superior adhesive and extreme pressure qualities, combined with it’s urethane compatibility makes it the only one to use.
With heims and uniballs you want to make sure you use the right lube and not a grease that attracts dirt. Tri-Flow Superior Lubricant is a superior, light viscosity lube that allows for deep penetration into hard to reach moving parts. The drip bottle application, with a convenient straw, allows for deep penetration in hard to reach moving parts.
Features and Benefits: Lifetime warranty. Dyno tested and proven to make power, performance gains in horsepower and torque, great sound – has a smooth; deep tone, easy to install, mandrel-bent. All welded. Built to last.
Features and Benefits: Lifetime warranty. Dyno tested ...
Perfect for maintaining an inconspicuous profile, black MAXTRAX are nearly invisible when mounted to your vehicle’s roof rack. This is the choice of colour for those in stealth mode. Just make sure to use your included leashes when they’re buried in the mud at night.
The SAFE, SIMPLE, QUICK and EASY vehicle recovery device. The carton includes 2 MAXTRAX and 2 orange telltale leashes (so you can find your MAXTRAX when they’re buried).
Perfect for maintaining an inconspicuous profile, ...
Camburg Engineering is the leader in off-road suspension systems and is at the forefront in technology and design. Our over the counter parts are being race tested constantly and have won numerous championships, so if you are looking for the most proven long travel or performance suspension systems Camburg is your #1 choice.